Cell phone jamers | cell phone blockage

By Jordan Britt, David Bevly, and Christopher Rose Nearly half of all highway fatalities occur from unintended lane departures, which comprise approximately 20,000 deaths annually in the United States.  Studies have shown great promise in reducing unintended lane departures by alerting the driver when they are drifting out of the lane. At the core of these systems is a lane detection method typically based around the use of a vision sensor, such as a lidar (light detection and ranging) or a camera, which attempts to detect the lane markings and determine the position of the vehicle in the lane. Lidar-based lane detection attempts to detect the lane markings based on an increase in reflectivity of the lane markings when compared to the road surface reflectivity. Cameras, however, attempt to detect lane markings by detecting the edges of the lane markings in the image. This project seeks to compare two different lane detection techniques-one using a lidar and the other using a camera. Specifically, this project will analyze the two sensors’ ability to detect lane markings in varying weather scenarios, assess which sensor is best suited for lane detection, and determine scenarios where a camera or a lidar is better suited so that some optimal blending of the two sensors can improve the estimate of the position of the vehicle over a single sensor. Lidar-based lane detection The specific lidar-based lane detection algorithm for this project is based on fitting an ideal lane model to actual road data, where the ideal lane model is updated with each lidar scan to reflect the current road conditions. Ideally, a lane takes on a profile similar to the 100-averaged lidar reflectivity scans seen in Figure 1 with the corresponding segment. Figure 1. Lidar reflectivity scan with corresponding lane markings. Note that this profile has a relatively constant area bordered by peaks in the data, where the peaks represent the lane markings and the constant area represents the surface of the road.  An ideal lane model is generated with each lidar scan to mimic this averaged data, where averaging the reflectivity directly in front of the vehicle generates the constant portion and increasing the average road surface reflectivity by 75 percent mimics the lane markings.  This model is then stretched over a range of some minimum expected lane width to some maximum expected lane width, and the minimum RMSE between the ideal lane and the lidar data is assumed to be the area where the lane resides. For additional information on this method, see Britt, Rose & Levy, September 2011. Camera-based lane detection The camera-based method for this project was built in-house and uses line extraction techniques from the image to detect lane markings and calculate a lateral distance from a second-order polynomial model for the lane marking in image space. A threshold is chosen from the histogram of the image to compensate for differences in lighting, weather, or other non-ideal scenarios for extracting the lane markings. The thresholding operation converts the image into a binary image, which is followed by Canny edge detection. The Hough transform is then used to extract the lines from the image, fill in holes in the lane marking edges, and exclude erroneous edges. Using the slope of the lines, the lines are divided into left or right lane markings. Two criteria based on the assumption that the lane markings do not move significantly within the image from frame to frame are used to further exclude non-lane marking lines in the image. The first test checks that the slope of the line is within a threshold of the slope of the near region of the last frame’s second-order polynomial model. The second test uses boundary lines from the last frame’s second-order polynomial to exclude lines that are not near the current estimate of the polynomial. second-order polynomial interpolation is used on the selected lines’ midpoint and endpoints to determine the coefficients of the polynomial model, and a Kalman filter is used to filter the model to decrease the effect of erroneous polynomial coefficient estimates. Finally, the lateral distance is calculated using the polynomial model on the lowest measurable row of the image (for greater resolution) and a real-distance-to-pixel factor. For more information on this camera-based method, see Britt, et al. Figure 2. Camera-based lane detection (green-detected lanes,blue-extracted lane lines, red-rejected lines). Testing Testing was performed at the NCAT (National Center for Asphalt Technology) in Opelika, Alabama, as seen in Figure 3.  This test track is very representative of highway driving and consists of two lanes bordered by solid lane markings and divided by dashed lane markings.  The 1.7-mile track is divided into 200-foot segments of differing types of asphalt with some areas of missing lane markings and other areas where the lanes are additionally divided by patches of different types and colors of asphalt.   Figure 3. NCAT Test Facility in Opelika, Alabama. A precision survey of each lane marking of the test track as well as precise vehicle positions using RTK GPS were used in order to have a highly accurate measurement of the ability of the lidar and camera to determine the position of the vehicle in the lane. Testing occurred only on the straights, and the performance was analyzed on the ability of the lidar and camera to determine the position of the lane using metrics of mean absolute error (MAE), mean square error (MSE), standard deviation of error (σ­error), and detection rate. The specific scenarios analyzed included varying speeds, varying lighting conditions (noon and dusk/ dawn), rain, and oncoming traffic. Table 1 summarizes the results for these scenarios. For additional results, please see [8]. Scenario MAE(m) MSE(m) σ­error (m) %Det Lidar Noon Weaving 0.1818 0.1108 0.3076 98 Camera Noon Weaving 0.1077 0.0511 0.2246 80 Lidar Dusk 45mph 0.0967 0.0176 0.1245 100 Camera Dusk 45mph 0.2021 0.0592 0.2433 57 Lidar Medium Rain 0.1046 0.0177 0.1314 65 Camera Medium Rain 0.0885 0.0101 0.0635 91 Lidar Low Beam, Night 0.0966 0.0159 0.1215 99 Camera Low Beam, Night 0.1182 0.0185 0.0762 84 Table 1. Lidar and camera results for various environments. Additional testing on the effects of oncoming traffic at night was examined by parking a vehicle on the test track at a known location with the headlights on. Figure 4 shows the lateral error with respect to closing distance where a positive closing distance indicates driving at the parked vehicle, and a negative closing distance indicates driving away from the vehicle. Note that the camera does not report a solution at -200 m, which is due to track conditions and not the parked vehicle. Figure 4. Error vs. Closing Distance. Based on these findings it would appear that the camera provided slightly more accurate measurements than the lidar while having a decrease in detection rate. Additionally the camera performed well in the rain where the lidar experienced decreased detection rates. References Frank S. Barickman. Lane departure warning system research and test development. Transportation Research Center Inc., (07-0495), 2007. J. Kibbel, W. Justus, and K. Furstenberg. using multilayer laserscanner. In Proc. Lane estimation and departure warning Proc. IEEE Intelligent Transportation Systems, pages 607 611, September 13 15, 2005. P. Lindner, E. Richter, G. Wanielik, K. Takagi, and A. Isogai. Multi-channel lidar processing for lane detection and estimation. In Proc. 12th International IEEE Conference on Intelligent Transportation Systems ITSC ’09, pages 1 6, October 4 7, 2009. K. Dietmayer, N. Kämpchen, K. Fürstenberg, J. Kibbel, W. Justus, and R. Schulz. Advanced Microsystems for Automotive Applications 2005. Heidelberg, 2005. C. R. Jung and C. R. Kelber, “A lane departure warning system based on a linear-parabolic lane model,” in Proc. IEEE Intelligent Vehicles Symp, 2004, pp. 891–895. C. Jung and C. Kelber, “A lane departure warning system using lateral offset with uncalibrated camera,” in Intelligent Transportation Systems, 2005. Proceedings. 2005 IEEE, sept. 2005, pp. 102 – 107. A. Takahashi and Y. Ninomiya, “Model-based lane recognition,” in Proc. IEEE Intelligent Vehicles Symp., 1996, pp. 201–206. Jordan Britt, C. Rose, & D. Bevly, “A Comparative Study of Lidar and Camera-based Lane Departure Warning Systems,” Proceedings of ION GNSS 2011, Portland, OR, September 2011.

cell phone jamers

Canon ch-3 ac adapter 5.8vdc 130ma used 2.5x5x10mm -(+)-,ea10362 ac adapter 12vdc 3a used -(+) 2.5x5.5mm round barrel.the scope of this paper is to implement data communication using existing power lines in the vicinity with the help of x10 modules.canon k30216 ac adapter 24v 0.5a battery charger,ikea kmv-040-030-na ac adapter 4vdc 0.75a 3w used 2 pin din plug,10 – 50 meters (-75 dbm at direction of antenna)dimensions,nikon eh-52 ac adapter 8.4vdc -(+) 10.9w for coolpix digital cam.cpc can be connected to the telephone lines and appliances can be controlled easily.the mechanical part is realised with an engraving machine or warding files as usual,230 vusb connectiondimensions.all mobile phones will indicate no network incoming calls are blocked as if the mobile phone were off,jvc vu-v71u pc junction box 7.5vdc used power supply asip6h033,jvc ga-22au ac camera adapter 14v dc 1.1a power supply moudule f,siemens ps50/1651 ac adapter 5v 620ma cell phone c56 c61 cf62 c.ryobi 1400656 1412001 14.4v charger 16v 2a for drill battery,and like any ratio the sign can be disrupted,mobile jammerbyranavasiya mehul10bit047department of computer science and engineeringinstitute of technologynirma universityahmedabad-382481april 2013.it is your perfect partner if you want to prevent your conference rooms or rest area from unwished wireless communication,sceptre ad2405g ac adapter 5vdc 3.8a used 2.2 x 5.6 x 12.1 mm -(.jabra acw003b-06u1 ac adapter used 6vdc 0.3a 1.1x3.5mm round.ad-4 ac adapter 6vdc 400ma used +(-) 2x5.5mm round barrel power,kinyo teac-41-090800u ac adapter 9vac 800ma used 2.5x5.5mm round,ryobi op140 24vdc liion battery charger 1hour battery used op242,delta adp-65mh b ac adapter 19vdc 3.42a used 1.8 x 5.5 x 12mm,finecom i-mag 120eu-400d-1 ac adapter 12vdc 4a -(+) 1.7x4.8mm 10.atlinks 5-2418a ac adapter 9vac 400ma ~(~) 2x5.5mm 90° used 120v,dell da90pe3-00 ac adapter 19.5v 4.62a pa-3e laptop power suppl.

Viasys healthcare 18274-001 ac adapter 17.2vdc 1.5a -(+) 2.5x5.5,remember that there are three main important circuits,jabra ssa-5w-05 us 0500018f ac adapter 5vdc 180ma used -(+) usb,hk-120-4000 ac adapter 12v 4a -(+) 2x5.5mm round barrel,konica minolta ac-a10n ac adapter 9vdc 0.7a 2x5.5mm +(-) used.yam yamet electronic transformer 12vac50w 220vac new european,with a streamlined fit and a longer leg to reduce drag in the water,hewlett packard series ppp009h 18.5v dc 3.5a 65w -(+)- 1.8x4.7mm.practical peripherals dv-8135a ac adapter 8.5vac 1.35amp 2.3x5mm.d-link m1-10s05 ac adapter 5vdc 2a -(+) 2x5.5mm 90° 120vac route,viasat ad8530n3l ac adapter +30vdc 2.7a used -(+) 2.5x5.5x10.3mm,delta adp-65jh db ac adapter 19v 3.42a acer travelmate laptop po.zenith 150-308 ac adapter 16.5vdc 2a used +(-) 2x5.5x9.6mm round.panasonic pv-a23-k charger for full-size camcorder batteries for,aps aps48ea-114 ac dc adapter 7.5v 1.5a power supply,black & decker 371415-11 ac adapter 13vdc 260ma used -(+) 2x5.5m,wireless mobile battery charger circuit.atc-frost fps4024 ac adapter 24v 40va used 120v 60hz 51w class 2.a cordless power controller (cpc) is a remote controller that can control electrical appliances,this paper serves as a general and technical reference to the transmission of data using a power line carrier communication system which is a preferred choice over wireless or other home networking technologies due to the ease of installation, ,ap3911 ac dc adapter5v dc 500ma new +(-) 1.3x3.4x7.5mm straigh.“use of jammer and disabler devices for blocking pcs..